| **CLICK ON PICTURES FOR MORE DETAILS** |
 |
| Stainless Wilson Case Trimmer |
|
| NOW IN STAINLESS
Wilson case trimmers are unique in that the case is held by a case holder which simulates a rifle chamber. Cases are held in case holders by their own body taper. The case holders sit in a rail system that also holds the cutter housing insuring square and perfect alignment every time. Trimmers can be held in a vise or are compatible with mounting stands. Trimmers can also be used for inside neck reaming, military crimp removal, and case mouth deburring by adding additional cutters. Specify (.17-.45), (.22-.45) or 50 Caliber case trimmer on order.
Suggested Retail: Standard Trimmer: $94.00 Regular Case Trimmer $96.00 17 Caliber Case Trimmer (Case Holder not included)
|
 |
| Stainless Trimmer with Micrometer Adjustment |
|
|
-
New Stainless long lasting finish with Micrometer adjustment
-
Larger stop screw adjustment from 3/8" (old) to 1/2" (new) with increased width on Stop Nut. Makes for a firm stop.
-
Major adjustment in the Stop Screw and fine adjustment by increments of .001 with the Micrometer
-
Bright Nickel Handle
-
Made in the U.S.A. with American Steel
-
Compatable with mounting stands
Suggested Retail: Stainless Trimmer with Micro Adjustment $160.00 (Case Holder not Included)
|
 |
| Stainless 50 Caliber Case Trimmer |
|
| NOW IN STAINLESS
- Oversized cutter to handle 50 Caliber cases (.610)
- Longer length to trim longer cases up to 3.925
- Stop screw diameter is 1/2" - 20 thread for fine adjustment and frim stop
- Trimmer will accept accessories such as - 50 Cal Primer Pocket Reamer (to remove military crimp), 50 Cal Inside Neck Reamer (available in .507 and .512 diameter) and the NEW Carbide Tip cutter.
- Compatable with 50 Caliber mounting stands
The 50 Caliber Trimmer is also compatable with all other case holders and will trim down to 6mm.
Suggested Retail: 50 Caliber Trimmer: $125.00 (Includes 50 BMG Case Holder)
|
 |
| Trimmer Stand and Case Holder Clamp |
|
| An alternative to mounting the trimmer in a vise. The Trimmer stand is available in the Regular and the 50 caliber verisons. Can be clamped or mounted to bench with screws.
Powder coated gun metal gray for a long lasting finish. Case Holder Clamp and Sinclair "Shark Fin" compatable
Case Holder Clamp is and alternative to holding the case holder down with your hand. All you need to do is set the Case Holder on the rails of the trimmer and then swing the clamp over the top. There is an adjustment on top of the clamp to increase or decrease pressure. Coated with a Bright Nickel Finish.
Comes with two screws to mount trimmer to stand. Bench mounting screws not provided.
Suggested Retail: Standard: $20.00 (Use with regular and SS trimmer) 50 Caliber: $24.00 (Use with 50 Cal Trimmer) Case Holder Clamp: $24.00 (Use with either Standard or 50 Cal Stand)
|
| Case Holders - For Use with Case Trimmer |
 |
| Rifle Case Holder |
|
| The case holder holds the case for trimming, primer pocket reaming, neck reaming and deburring with our Uniform Deburring Tool.
Suggested Retail: $14.00 rifle $22.00 special case holders
*Special case holders can be made upon request. Please send in three cases in the condition in which you intend to trim them (ex. new, fired or sized). The charge is $22.00 USD plus shipping of $8.50 for U.S. Customers. Please include a check or money order with your cases. See Contact Us link for shipping address.
|
 |
| Hardened Pistol Holder |
|
| Pistol Holders are for straight walled cases with no belt. These cases must be tapped in and out with a plastic mallet or pressed in and out with an arbor press. The best method is to use an arbor press to press in, then using a piece of wooden dowl press the case out. It is a much slower process then the rifle cases but it does create a very accurate cut. These are designed for fired cases.
Suggested Retail: $20.00
|
 |
| Q-Type Holder |
|
| Case Holders allow you to trim cases in your Wilson Case Trimmer. The Q-Type case holders hold the case with an easy to use cross pin. Use this type whenever possible because the regular pistol case holders require you to tap the pistol case in, which is more difficult than the rifle cases because of the lack of a body taper.
Suggested Retail: $26.00
|
| Case Prep Tools - For Use with Case Trimmer |
 |
| Cutters |
|
| We have two differect cutters sizes available for the regular case trimmer, one for .17 caliber and one for .22 - .45. The trimmer cutter is designed to trim cases to length and has been perfected over the last 70+ years to give you a flat square cut with little effort. Hardened to 60 Rockwell.
17 Caliber Cutter = .17 cal cases (will also trim up to .45) Trimmer Cutter = Cases up to .490 (.22 - .45)
Note: To be used with the Regular or Stainless Steel Case Trimmer, Power Adaptor compatable
Suggested Retail: .17 Cal Cutter $34.00 Trimmer Cutter $30.00
|
 |
| 50 Caliber Cutter |
|
| Made in the same process as the regular cutter only slightly oversized. The trimmer cutter is designed to trim cases to length and will give you a nice flat cut every time. Hardened to 60 Rockwell.
50 Caliber = Cases .490 - .605 (.50)
Note: To be used with the 50 Caliber Case Trimmer, Power Adaptor compatable
Suggested Retail: 50 Caliber Cutter $45.00
|
 |
| Carbide Cutter |
|
|
- For use with Regular Case Trimmer
- Accepts L.E. Wilson standard handle
- Same degree and rake as standard cutter
- Long lasting durable cutting edge
- Power adaptor compatable
Suggested Retail: $60.00
|
 |
| 50 Caliber Carbide Cutter |
|
|
- For use with 50 Caliber Case Trimmer
- Accepts L.E. Wilson standard handle
- Same degree and rake as standard cutter
- Long lasting durable cutting edge
- Power Adaptor compatable
Suggested Retail: $75.00
|
 |
| Deburring Tool - For use with trimmer |
|
| We produce two case mouth deburring tools for use in the Case Trimmer. The deburring tools mount in the cutter housing and each includes a crank style handle. Cases are inserted into the trimmer case holders and are held square to the deburring tool. Available in both standard 45 degree and 30 degree chamfer. Handle included.
Suggested Retail: $34.00
|
 |
| Primer Pocket Reamer |
|
| Used in conjunction with the Case Trimmer to remove the primer pocket crimp on military cases. The finished result is a nice rounded entry for primers. Unlike some tools this tool will not distort the case head. Specify large (.210) small (.175) or 50 Cal primer pockets when ordering. Comes with handle.
Suggested Retail: $44.00 (.175 or .210) $60.00 (50 Cal)
|
 |
| Inside Neck Reamer |
|
| Thick necks can cause high chamber pressures and erratic shooting. Neck reamers remove excess neck material to insure adequate clearance exists between the case neck and the chamber. Also, these reamers can be used when forming wildcats from a parent case. Reamers are used in the trimmers in place of the trimmer cutter. Standard reamers are sized for use on fired, unsized cases. Special sizes can be ground but will extend lead time.
Suggested Retail: $38.00 Standard Sizes $48.00 Specials (Check avalibility) $64.00 50 Cal (.5120 - .5125)
|
| Inside / Outside Deburring Tool |
 |
| Deburring Tool |
|
| All cases should be case mouth deburred after trimming and neck turning. Tools are double-ended with standard 45-degree flutes that debur/chamfer the inside and outside mouth of the case. They will work on cases from .17 to .45 and .50 caliber.
Suggested Retail: $20.00 (.17-.45) $28.00 (50 Cal)
|
| Neck Dies and Decapping Sets |
 |
| Stainless Steel Neck Die |
|
| NOW ALL NECK DIE CALIBERS IN STAINLESS
Designed so the user can control and/or change the amount of neck sizing the cartridge case receives. Uses interchangeable sizing bushings that size the outside of the case neck. The conventional expander is eliminated, improving concentricity and prolonging brass life. The die is used with an Arbor Press. Sizes the neck to 3/16" from the mouth end, a practice many shooters prefer. Bushings not included. Dies include a decapping rod.
Suggested Retail: $78.00 without bushing
|
 |
| Neck Die Bushing |
|
| The Neck Die Bushing fits in the Neck Die and sizes the case neck to grip the bullet.
To figure out what size to order... Measure the diameter of a loaded round where the bullet sits in the neck (Ex. .268). Now subtract .002 to .003 from that number.
.268 -.002 = .266 Bushing
Another way is to measure your wall thickness and multiply by 2 and add bullet diameter. Then subtract .002 to .003 from that number.
.012 Wall Thickness x 2 = .024 .243 Bullet Diameter Example: .243 + .024 = .267 Now subtract .003 (.267 - .003 = .264 Bushing)
Suggested Retail: $20.00
|
 |
| Punch and Decapping Base |
|
| The punch and base decaps the primer from the case while providing a stable base.
Suggested Retail: $22.00 Punch and Base Set $14.00 Punch $8.00 Base
|
 |
| Chamber Type Bullet Seater |
|
| A favorite among benchrest shooters. A chamber type bullet seater positively controls both bullet and cartridge case alignment. The case and bullet are completely captured by the die prior to the bullet being pushed straight into the case by a close-fitting seating stem. This style of bullet seater works more accurately than a conventional (7/8"-14) bullet seating die. This is one of the most accurate bullet seaters ever made.
Suggested Retail: $66.00
|
 |
| Stainless Steel Bullet Seater with Micrometer Adjustment |
|
| The most accurate and easiest to use straight line dies on the market. The stainless seaters have a built in micrometer seating depth adjustment feature with an easy to read scale in .001 graduations.
Suggested Retail: $130.00
|
 |
| Case Gage |
|
| One piece gage that will check overall length to indicate the need for trimming, datum to head length to assure correct headspace and to prevent over sizing. Available for most popular rimless cases.
Note: Does not measure body diameters. This gage is intended to be used with fired cases to determine a basis for full length sizing and trimming.
Suggested Retail: $36.00 Standard $60.00 50 BMG
|
 |
| Adjustable Case Gage |
|
| For belted mags. While the belt provides support for proper headspace, the life of the case will drastically shorten unless resizing is held to a minimum at the shoulder. These gages, which can be adjusted to be used with individual rifles of the same caliber, will enable the handloader to control the amount of resizing simply by measuring a fired case. Overall length can also be checked with these gages.
Suggested Retail: $46.00
|
 |
| Case Length Gage |
|
| One-piece, non adjustable cylinder-type gage with milled surfaces on one end for checking minimum and maximum overall length of rifle and pistol cases having no shoulder.
Suggested Retail: $22.00
|
 |
| Pistol Max Gage |
|
| The Pistol Max Gage measures the maximum dimensions of a loaded round. This includes case length, max chamber dimensions, and max length of loaded round.
Suggested Retail: $28.00
|
|